-
KL2012 | Bus Terminal, 2-channel digital output, 24В VВ DC, 0.5В A
0,00 ₽The KL2012 digital output terminal connects the binary control signals from the automation unit on to the actuators at the process level with electrical isolation. It handles different load currents, and its outputs are protected against overload and short-circuit. The Bus Terminal contains two channels that indicate their signal state by means of light emitting diodes.
-
KL2022 | Bus Terminal, 2-channel digital output, 24В VВ DC, 2В A
0,00 ₽The KL2022 digital output terminal connects the binary control signals from the automation unit on to the actuators at the process level with electrical isolation. It handles different load currents, and its outputs are protected against short-circuit. The Bus Terminal contains two channels that indicate their signal state by means of light emitting diodes.
-
KL2032 | Bus Terminal, 2-channel digital output, 24В VВ DC, 0.5В A, reverse voltage protection
0,00 ₽The KL2032 digital output terminal connects the binary control signals from the automation unit on to the actuators at the process level with electrical isolation. It is protected against reverse polarity connection. The Bus Terminal contains two channels that indicate their signal state by means of light emitting diodes.
-
KL2114 | Bus Terminal, 4-channel digital output, 24В VВ DC, 0.5В A
0,00 ₽The KL2114 digital output terminal connects the binary control signals from the automation unit on to the actuators at the process level with electrical isolation. The load current output of the KL2114 is protected against overload and short-circuit. The Bus Terminal contains four channels that indicate their signal state by means of light emitting diodes.
-
KL2134 | Bus Terminal, 4-channel digital output, 24В VВ DC, 0.5В A, reverse voltage protection
0,00 ₽The KL2134 digital output terminal connects the binary control signals from the automation unit on to the actuators at the process level with electrical isolation. The KL2134 is protected against reverse polarity connection. The Bus Terminal contains four channels that indicate their signal state by means of light emitting diodes.
-
KL2184 | Bus Terminal, 4-channel digital output, 24В VВ DC, 0.5В A, ground switching
0,00 ₽The KL2184 digital output terminal connects the binary control signals from the automation unit on to the actuators at the process level with electrical isolation. It has four ground switching outputs and generates load currents with outputs that are resistant to overload and short-circuit. The Bus Terminal contains four channels that indicate their signal state by means of light emitting diodes.
-
KL2284 | Bus Terminal, 4-channel digital output, reverse switching, 24В VВ DC, 2В A
0,00 ₽The KL2284 output terminal switches loads in selectable polarity. This means that DC motors can be used in both directions of rotation. A polarity is switched with two output bits per channel. An interlock prevents simultaneous switching of both directions. Advanced power semiconductors enable safe and wear-free switching with minimum dimensions. The high starting and short-circuit currents of the KL2284 are comparable with a robust relay. The number of switching cycles is almost unlimited.
-
KL2404 | Шинный терминал, 4-канальный цифровой выход, 24В В постоянного тока, 0,5В А, 2-проводное соединение
0,00 ₽Цифровой выходной терминал KL2404 соединяет двоичные сигналы управления 24 В, электрически изолированные с исполнительными механизмами. Шинный терминал содержит четыре канала, которые показывают состояние сигнала с помощью светодиодов. 4-канальный шинный терминал обеспечивает прямое подключение четырех 2-проводных датчиков. Предусмотрены четыре точки заземления.
-
KL2442 | Bus Terminal, 2-channel digital output, 24В VВ DC, 2В xВ 4В A/1В xВ 8В A
0,00 ₽The KL2442 digital output terminal connects the binary 24 V control signals, electrically isolated, with the actuators. Two channels are available and indicate their signal state via LEDs. The KL2442 enables connection of loads with current consumption up to 8 A if the outputs are connected in parallel.
-
KL2488 | Bus Terminal, 8-channel digital output, 24В VВ DC, 0.5В A, ground switching
0,00 ₽The KL2488 (ground switching) digital output terminal connects the binary control signals from the automation unit on to the actuators at the process level with electrical isolation. It is protected against reverse polarity connection and handles load currents with outputs that are protected against overload and short-circuit. The Bus Terminal contains eight channels which indicate their signal state by means of light emitting diodes. It is particularly suitable for space-saving use in control cabinets. The connection technology is optimized for single-ended inputs. All components have to use the same reference point as the KL2488. The power contacts are looped through. The outputs are supplied by the 0В V power contact.
-
KL2502 | Bus Terminal, 2-channel PWM output, 24В VВ DC, 0.1В A
0,00 ₽Выходной терминал KL2502 модулирует ширину импульса двоичного сигнала 24В В постоянного тока и выводит его электрически изолированным от K-bus. Соотношение метка/пробел предписывается 16В битным значением от устройства автоматизации. Выходной каскад защищен от перегрузки и короткого замыкания. Bus Terminal имеет два канала, состояние сигнала которых отображается светодиодами. Светодиоды управляются синхронно с выходами и показывают коэффициент заполнения своей яркостью.
-
KL2532 | Bus Terminal, 2-channel motion interface, DC motor, 24В VВ DC, 1В A
0,00 ₽The KL2532 Bus Terminal enables direct operation of two DC motors. It is galvanically isolated from the K-bus. The speed is preset by a 16 bit value from the automation unit. The output stage is protected against overload and short-circuit. The Bus Terminal contains two channels that indicate their signal state by means of light emitting diodes. The LEDs enable quick local diagnosis.
-
KL2545 | Bus Terminal, 2-channel PWM output, 8…50 V DC, 3.5 A, current-controlled
0,00 ₽The KL2545 output terminal controls an output current via pulse width control of the supply voltage. It is galvanically isolated from the K-bus. The current value (0 to В±3.5 A) is specified by the automation device via a 16 bit value. The output stage is protected against overload and short-circuit. The Bus Terminal contains two channels that indicate their signal state by means of light emitting diodes. The LEDs simplify local diagnosis by displaying typical load and wiring faults.
-
KL2552 | Bus Terminal, 2-channel motion interface, DC motor, 48В VВ DC, 5В A
0,00 ₽The KL2552 Bus Terminal enables direct operation of two DC motors. It is galvanically isolated from the K-bus. The speed is specified by the automation device via a 16В bit value. Connection of an incremental encoder enables a simple servo axis to be realized. Typical motor parameters can be set in order to avoid critical conditions of the DC motor. The load can be protected by limiting the maximum values for speed, torque and acceleration. The output stage is protected against overload and short-circuit. The Bus Terminal contains two channels that indicate their signal state by means of light emitting diodes. The LEDs enable quick local diagnostics.
-
KL2602-0010 | Bus Terminal, 2-channel relay output, 230В VВ AC, 30В VВ DC, 5В A, contact-protecting switching
0,00 ₽The KL2602-0010 output terminal has two relays each of which has a single contact. The relay terminal is designed for soft switching at the zero voltage crossing to protect the contacts and is particularly suitable for capacitive loads such as LED lamps. The Bus Terminal indicates its signal state by means of light emitting diodes.
-
KL2622-0010 | Шинный терминал, 2-канальный релейный выход, 230В В перем. тока, 30В В пост. тока, 5В А, переключение с защитой контактов, без силовых контактов
0,00 ₽Выходной терминал KL2622-0010 имеет два реле, каждое из которых имеет один контакт. Релейный терминал предназначен для мягкого переключения при переходе через нуль напряжения для защиты контактов и особенно подходит для емкостных нагрузок, таких как светодиодные лампы. Контакты питания не закольцованы. Терминал EtherCAT отображает состояние своего сигнала с помощью светодиодов.
-
KL2652 | Bus Terminal, 2-channel relay output, 230В VВ AC, 300В VВ DC, 5В A
0,00 ₽The KL2652 output terminal has two relays, each featuring a change-over contact. The relay contact can be used universally for switching devices requiring mains power up to 230 V AC or 300 V DC. The KL2652 Bus Terminal is equipped with potential-free contacts. The signal state of the Bus Terminal is indicated via LEDs.
-
KL2692 | Bus Terminal, 2-channel relay output, cycle monitoring, 30В VВ DC, 3В A
0,00 ₽The KL2692 Bus Terminal monitors a bit that is toggled by the controller during each cycle. If the toggle signal fails, the controller switches off two potential-free relay circuits in order to prevent damage to the machine. Failure of the toggle signal may be caused by the PLC cycle stopping, by a fault in the bus cable or connector, or by a fault in a bus device. The cycle monitoring time can be parameterized. The Bus Terminal has an enable input that enables the relay to be switched on if a correct toggle signal is detected.
-
KL2701 | Bus Terminal, 1-channel solid-state relay output, 0…230 V AC/DC, 3 A
0,00 ₽The KL2701 output terminal uses an electronic load relay to switch a mains voltage of up to 230В VВ AC/DC with an output current of 3В A. The switching element is a high-power MOSFET, which is connected to the power contact potential. As a semiconductor switch, it is not subject to wear. The KL2701 terminal has one independent output. Its signal state is indicated by means of a light emitting diode.
-
KL2702 | Шинный терминал, 2-канальный твердотельный релейный выход, 0–230 В В переменного/постоянного тока, 0,3 В А
0,00 ₽The KL2702-xxxx output terminal uses an electronic load relay to switch a mains voltage of up to 230В VВ AC/DC. The switching element is a high-power MOSFET, which is connected to the power contact potential. As a semiconductor switch, it is not subject to wear. The terminal has two outputs that indicate their signal state via LEDs.
-
KL2732 | Bus Terminal, 2-channel triac output, 12…230В VВ AC, 1В A, without power contacts
0,00 ₽The KL2732 output terminal uses a power switch to control mains voltage from 12 V to 230 V AC. The switching element is a triac. As a semiconductor switch, it is not subject to wear. The KL2732 has two mutually locked outputs and operates with two potential-free switches. The terminal is most suitable for reverse motors.
-
KL2761 | Bus Terminal, 1-channel universal dimmer, 230В VВ AC, 600В VA
0,00 ₽Шинный терминал диммера KL2761 предназначен для прямого подключения различных осветительных приборов. Регулируемые осветительные приборы, такие как лампы накаливания, индуктивные и электронные балласты, обнаруживаются и контролируются в правильном рабочем режиме. Требуемые значения яркости указываются через данные процесса. KL2761 вычисляет правильный угол фазового управления при управлении фазой по переднему или заднему фронту для требуемого значения. Выход защищен от короткого замыкания и перегрузки. KL2761 может работать на любой полевой шине. Можно считывать состояние нагрузки.
-
KL2784 | Bus Terminal, 4-channel solid state relay output, 30В VВ AC, 48В VВ DC, 2В A
0,00 ₽The digital KL2784 Bus Terminal provides four switches that can be used like a relay contact for AC/DC voltages. The electronic switch is realized through high-performance MOSFET transistors with low switch-on resistance. The switch itself is not short-circuit proof, but due to its high pulse current capability it can cope with current until an external fuse triggers a switch-off.
-
KL2791 | Bus Terminal, 1-channel motion interface, AC motor, 230В VВ AC, 0.9В A
0,00 ₽The KL2791-xxxx AC motor speed controller is intended for direct connection of different low-power single-phase AC motors. The KL2791 enables speed reduction of typical motors such as capacitor motors, universal motors and shaded-pole motors. The required output power is specified via the process data. The output setting matches respective output value through targeted on and off switching at optimized times. This technique is particularly suitable for drives with quadratic load characteristic such as fans and pumps.
-
KL2794 | Bus Terminal, 4-channel solid state relay output, 30В VВ AC, 48В VВ DC, 2В A, potential-free
0,00 ₽The digital KL2794 Bus Terminal provides four potential-free semiconductor switches that can be used like a relay contact for AC/DC voltages. The electronic switch is realized through high-performance MOSFET transistors with low switch-on resistance. The switch itself is not short-circuit proof, but due to its high pulse current capability it can cope with current until an external fuse triggers a switch-off.
-
KL2819 | Bus Terminal, 16-channel digital output, 24В VВ DC, 0.5В A, with diagnostics
0,00 ₽The KL2819 Bus Terminal has 16 digital output channels for the switching of 24В V loads up to 0.5В A. The integrated diagnostics can be evaluated by the controller and indicated by the LEDs. Overtemperature and the lack of a voltage supply to the terminal are supplied as diagnostic information. Moreover, each of the channels can signal e.g. a short circuit. The switching state and any error of the output are indicated by the LED. Maintenance of the application is simplified by the diagnostic function. The power contacts are connected through, reference ground of the outputs is the 0В V power contact. The outputs are electrically isolated from the fieldbus side.
-
KM2002 | Модуль шинного терминала, 16-канальный цифровой выход, 24В В постоянного тока, 0,5В А
0,00 ₽Терминальный модуль KM2002 объединяет 16 цифровых выходов с восемью каналами на каждый разъем в компактном исполнении. Двоичные сигналы управления передаются (электрически изолированы) на исполнительные механизмы на уровне процесса. Как и стандартные шинные терминалы, терминальные модули интегрированы в систему ввода-вывода.
-
KM2008 | Bus Terminal module, 64-channel digital output, 24В VВ DC, 0.5В A
0,00 ₽The KM2008 terminal module combines 64 digital outputs with each eight channels per connector in a compact design. The binary control signals are transferred (electrically isolated) to the actuators at the process level. Like the standard Bus Terminals, the terminal modules are integrated in the I/O system.
-
KM2642 | Bus Terminal module, 2-channel digital output, 230В VВ AC, 6В A, manual/automatic operation
0,00 ₽The digital KM2642 output terminal has two independent relay change-over contacts, which can be used for switching mains current consumers. For each channel a switch enables selection between automatic, manual on, manual off. In automatic mode the logical state of an output bit switches the relay. For manual mode a 24В V supply is required for the Bus Coupler. The output state can be read by the controller.
-
KM2652 | Bus Terminal module, 2-channel digital output, 230В VВ AC, 6В A, manual/automatic operation
0,00 ₽The digital KM2652 output terminal has two independent relay change-over contacts, which can be used for switching mains current consumers. For each channel a switch enables selection between automatic, manual on, manual off. In automatic mode the logical state of an output bit switches the relay. For manual mode a 24В V supply is required for the Bus Coupler. The output state as well as the setting of the switch can be read by the controller.
-
KM2774 | Bus Terminal module, 4-channel triac output, 80…230 V AC, 1.5 A
0,00 ₽The compact KM2774 module enables direct connection of up to four AC motors with reversal of rotation direction and a further travel function. For each motor, three mutually locked Triac outputs with 230 V AC and up to 1.5 A are available. The outputs are protected against overload. An adjustable overcurrent limit protects the motor from damage. The typical control signals can be wired via 24 V inputs. Status and error messages are available via the fieldbus and via LED at the module.
